Leduc's Local
Garage Heater Install
Company

There are several steps involved in installing your new furnace. These steps will vary depending on the furnace you choose, your home’s existing furnace system, and any changes you want.

1. Align the new furnace with existing gas lines and ductwork
2. Connect and seal to the ducting system
3. Connect intake and exhaust pipes
4. Connect the gas line
5. Connect the furnace to the electrical supply and thermostat
6. Connect the furnace to a drain hole

At this point, it’s important to check your work, make sure everything is connected properly and there are no gas leaks. 

Please note: these steps are extremely simplified and meant to provide an overview to understand the professional furnace installation process better. It is highly recommended that you have your furnace professionally installed in order to avoid dangerous problems and issues with your new furnace. Having to get furnace repairs on your new unit would not be covered under warranty without professional installation.

Hiring a professional will be more costly initially but will save you money in the long run.

Here’s how long it takes to install a new furnace.

Boilers can last a really long time. In fact, the average lifespan of a boiler is 10 to 15 years. In order to extend the life of your boiler, it’s important to ensure that it is properly maintained and serviced on a regular basis. Even the best boiler will require maintenance and repairs from time to time.

If your boiler is giving you signs that it needs attention, make sure to call the Pros at ProSolutions for regular maintenance and fast repairs. This will ensure your boiler lasts as long as possible. Some signs to keep an eye out for include: low water pressure, no heat coming from your radiators, banging noises, a pilot light that keeps going out or isn’t blue.

Shopping for a new furnace and wondering what are BTUs? BTU stands for British Thermal Unit – a value traditionally assigned to heat. Technically, a single BTU is the amount of energy that is necessary to increase the temperature of one pound of water by one degree Fahrenheit at sea level. As far as a heating system goes, BTUs refer to the amount of heat that a furnace is able to output.

When it comes to furnaces, the larger the square footage that needs to be heated, the more BTUs you’ll require. For example, it’s suggested that a 1,500 square foot home has a furnace that is able to output 45,000 to 90,000 BTUs.

A modern, high-efficiency furnace should last approximately ten to fifteen years. This is based on the average lifespan of a furnace so it is possible that yours may last longer or need to be replaced sooner. 

The key to a long-lasting furnace is regular maintenance and upkeep. It’s important to stay on top of minor furnace repairs, tune-ups, and maintenance. Scheduling regular maintenance with a professionals heating company will help to maximize the life of your furnace and minimize the need for major repairs. This is especially true in Alberta, where cold winters can take a toll on your furnace.

A local furnace company will know how to care for your furnace in this climate and what to look for if it is having issues.

A professional technician will have an extensive checklist to go through when providing furnace tune-up service and maintenance. The items on this list cover every part of your furnace in order to ensure that it is in top working condition.

Some of the most important items included in this furnace service checklist are:

• Vent, blower, and ductwork cleaning
• Inspection of the flue for damage and dents
• Examination of all belts and their tension
• Adjustment of the furnace’s pilot light flame
• Calibration of the thermostat
• Visual inspection of all electrical wiring
• Inspection of the furnace filter
• Cleaning and removing any debris

A checklist that includes no less than 22 points of inspection should be used during your furnace service.

Furnace on the fritz? Here are a few things to check if your furnace isn’t working:

• Power switch – is the power on? If so, try turning the furnace off and then on again.
• Furnace filter – check to see if the filter is clogged. If it is, exchange it for a new one. You should be changing your furnace filter ever 3 months.
• Batteries in the thermostat – check the batteries in your thermostat and replace them if they’re low.
• Flame sensor – turn off the power to your furnace (this is an important first step) then remove the sensor and clean it.
• Pilot light – check to make sure the pilot light is on. If it’s out, relight it using your furnace model’s igniting instructions.
• Air intake and exhaust pipes – check the exhaust flue for blockages and clear any blockage you find. For example, during the winter in Alberta, you might find icicles covering the screen of the flue. Remove these to solve the problem.

If one of these is not the issue, you may need a professional to help you uncover and solve the problem. Don’t wait until it’s too late – a broken furnace, especially during an Edmonton winter, can result in broken and burst water pipes! Find a local furnace repair contractor to fix the problem as soon as possible.

It can cost anywhere from $150 to $1,500 to repair a furnace, depending on the issue. If you’re in the Edmonton area, the average cost to repair a furnace will be around $700.

Make sure the furnace company you choose to do your repairs is upfront with their pricing. They should be able to provide you with the price ahead of time so that you know exactly what to expect before moving ahead!

Want to save some money? Often professional heating and plumbing companies will offer a Service Partner Plan – we call ours the ProComfort Plan. This type of plan will help you keep on top of the regular maintenance your furnace needs for a fraction of the price. Regular furnace tune-ups and maintenance will help prevent any major issues, saving you from repairs and replacements that could cost you thousands of dollars! With plans like this, there is often a discount for members, meaning you’ll save money with every visit.

In the Edmonton area, you should typically change your furnace filter every 1 to 3 months—but it depends on your home and lifestyle:

• Every 1 month if you have multiple pets, allergies, or live in a dusty area

• Every 2 months for average homes with one pet or light allergies

• Every 3 months in smaller homes with no pets and minimal dust

• More often during heavy-use seasons, like winter (heating) and summer (if you use central AC)

Filter size and quality also play a role—smaller or lower-MERV filters usually need changing more frequently.

If you’re tired of remembering when to replace them, our ProComfort Dual and ProHeating Memberships offer an Air Filter Delivery Add-On. We’ll deliver the right filters to your door on schedule—so your home stays clean, your air stays fresh, and your HVAC system runs at its best without any guesswork.