Ft. Saskatchewan's Preferred
Plumbing Service 
company

On average, sump pumps last about 10 years. As with any other appliance in your home, a sump pump can become damaged and may need to be replaced as it gets older or experiences more use. Unfortunately, unlike other appliances, it isn’t always obvious when a sump pump has reached the end of its life. In fact, this isn’t usually detected until the sump pump should be working but fails to do its job. In order to prevent your sump pump from failing when you need it most, it’s important to contact a professional plumber nearby to provide sump pump services if you notice that there is no water in the sump pit when your pump is running, if you see rust, if there is a musty or dank odour in your basement, if you hear strange noises coming from your sump pump or if the pump is failing to run automatically.

The amount of time it takes to get hot water from a new water heater depends on the size and type of hot water heater. A properly and professionally installed gas hot water heater will provide hot water most quickly. An average 40-gallon heater will only take about 30 to 40 minutes to provide heat water, while you can expect hot water from a larger tank (80-gallons) in approximately 60 to 70 minutes. Electric hot water tanks, on the other hand, will take a little longer. For an average 40-gallon electric heater it will take about 60 to 80 minutes and for an 80-gallon tank about 2 hours.

You can’t run out of hot water with tankless water heaters – unless, of course, the power supply is off or goes out. However, a tankless water heater can have trouble keeping up with demand if too many things require hot water all at once. For example, if several appliances are operating at the same time (the dishwasher, the laundry machine, etc.), and you go to have a hot shower, you may find that your tankless unit isn’t capable of providing enough hot water. Therefore, it’s important to ensure that you install a tankless water heater that has a large enough capacity to handle your demand for hot water.

Installing a water softener doesn’t take too long when a professional technician is completing the installation. As long as no unforeseen setbacks or problems are encountered, a professional plumber should be able to install a water softener in about two to three hours. Choosing to have your water softener installed by an expert is a good idea, as this will ensure that it is installed and working properly, helping to prevent problems down the road. In addition, water softeners are available in various makes and models and an experienced technician can help you find the best system for your home and your family.

The time it takes to repair a burst pipe can vary based on the location and severity of the break. A simple repair might take a few hours, while more complex situations could require several days. Water damage restoration, depending on the extent of the damage, can take anywhere from a few days to several weeks. It’s crucial to address water damage promptly to prevent mold growth and further structural issues.

Remember, in the event of a burst pipe, it’s essential to act quickly to minimize damage and ensure the safety of everyone in the home.

Drain cleaners can be bad for pipes. This is particularly true for chemically costic drain cleaners. 

Chemical drain cleaners create a chemical reaction in your pipes. This results in heat being emitted. It is this heat that can be bad for your pipes. Older and plastic pipes, especially, can be damaged by chemical drain cleaners. If you have plastic pipes and you use a chemical cleaner, the heat may melt the plastic. This can result in leaks and further damage. As well, drain cleaners are not good for septic systems.

To avoid damaging your pipes, try another method of unclogging your pipe first. If you’re unsure, call a professional drain cleaning plumber services provider to help you get the job done right.

ProSolutions Inc. stands out due to our commitment to fast and reliable service, especially in emergencies like burst pipes. With over 30 years of experience in Edmonton, our trained residential plumbers are equipped with advanced tools and technology to handle burst pipe repairs efficiently. Plus, our upfront pricing ensures no hidden costs, and our no overtime fee policy guarantees affordability even in emergencies.

It can cost anywhere from $3,500 to $5,500 to get a water softener installed in your home. This estimate includes the price of the unit as well as installation. The total cost will range depending on several factors including the type of water softener you choose, the softener’s capacity, the size of your home and the difficulty of the installation. In order to avoid unnecessary costs down the road, it’s important that you have your water softener installed by an expert. Water softener installation in Edmonton is ideal, especially if you are constantly having to deal with soap scum and limescale buildup or you want to increase the longevity of your household appliances that use water.